Modbus Map | Guide TEST

The table below shows the complete Modbus map:

Scope	Group	Table	Address	Description	Data Type	Size	Access
Bridge	GeneralInfo	Input regs	0	Device name	str	30	Read
Bridge	GeneralInfo	Input regs	15	DALI bridge application version	buf	8	Read
Bridge	GeneralInfo	Input regs	19	Number of available DALI buses	u16	2	Read
Bridge	GeneralInfo	Input regs	20	Bitmask of device error flags bit 0 = Flash write failed bit 1 = Invalid factory data bit 2 = Sync failed bit 3 = Firmware upgrade failed bit 4:31 = reserved	u32	4	Read
Bridge	GeneralInfo	Input regs	22	Bitmask of device warning flags bit 0 = Time not valid bit 1 = Network disconnected bit 2 = Network not configured bit 3:31 = reserved	u32	4	Read
Bridge	GeneralInfo	Input regs	24	Bitmask of device info flags bit 0:31 = reserved	u32	4	Read
Bridge	WritableCommands	Holding regs	0	Restart DALI bridge (1 = trigger software reboot) Read = last written command	u16	2	Read/Write
Bridge	WritableCommands	Holding regs	1	Turn all lights ON/OFF (1 = ON, 0 = OFF) Read = last written command	u16	2	Read/Write
DALIBus #1	GeneralInfo	Input regs	2048	Name DALI bus 1	str	20	Read
DALIBus #1	GeneralInfo	Input regs	2058	DALI bus 1 controller application version	buf	4	Read
DALIBus #1	GeneralInfo	Input regs	2060	Configured zones bitmask bit 0 = Zone 1 bit 1 = Zone 2 bit 2 = Zone 3 bit 3 = Zone 4 bit 4 = Internal relay bit 5:15 = reserved	u16	2	Read
DALIBus #1	GeneralInfo	Input regs	2061	Number of luminaires on DALI bus 1	u16	2	Read
DALIBus #1	GeneralInfo	Input regs	2062	Number of input devices on DALI bus 1	u16	2	Read
DALIBus #1	GeneralInfo	Input regs	2063	Measured light intensity (lux)	u32	4	Read
DALIBus #1	GeneralInfo	Input regs	2065	PIR motion status	u16	2	Read
DALIBus #1	GeneralInfo	Input regs	2067	Bitmask of DALI bus 1 error flags bit 0 = Flash write failed bit 1 = Master firmware version mismatch bit 2:31 = reserved	u32	4	Read
DALIBus #1	GeneralInfo	Input regs	2069	Bitmask of DALI bus 1 warning flags bit 0 = reserved bit 1 = Missing short address bit 2 = P40 master missing bit 3 = Control gear failure bit 4 = Lamp failure bit 5 = Bus voltage too low bit 6 = Bus shorted bit 7 = Bus overloaded bit 8:31 = reserved	u32	4	Read
DALIBus #1	GeneralInfo	Input regs	2071	Bitmask of DALI bus 1 info flags bit 0 = Identify device active bit 1:2 = reserved bit 3 = Multiple backward frames bit 4:31 = reserved	u32	4	Read
DALIBus #1	WritableCommands	Holding regs	2048	Turn all connected zones ON/OFF Read = last written command	u16	2	Read/Write
DALIBus #1	WritableCommands	Holding regs	2049	Lux setpoint - all zones Read = last written command	u16	2	Read/Write
DALIBus #1	WritableCommands	Holding regs	2050	Switch off delay after no motion - all zones (seconds) Read = last written command	u32	4	Read/Write
DALIBus #1	WritableCommands	Holding regs	2052	Orientation light switch-off delay - all zones (seconds) Read = last written command	u32	4	Read/Write
DALIBus #1	WritableCommands	Holding regs	2054	Light level - all zones Read = last written command	u16	2	Read/Write
DALIBus #1	WritableCommands	Holding regs	2056	Identify P40 master detector (1 = identify, auto-resets after execution) Read = 1 while identify is active	u16	2	Read/Write
DALIBus #1	Zone_1_DataInfo	Input regs	2304	Zone 1 light status (ON/OFF)	u16	2	Read
DALIBus #1	Zone_1_DataInfo	Input regs	2305	Zone 1 light level (0-100%)	u16	2	Read
DALIBus #1	Zone_1_DataInfo	Input regs	2306	Zone 1 lux setpoint	u16	2	Read
DALIBus #1	Zone_1_DataInfo	Input regs	2307	Zone 1 energy consumption (Wh)	u64	8	Read
DALIBus #1	Zone_1_DataInfo	Input regs	2312	Zone 1 operation mode (0 = DALI bridge controlled, 1 = detector controlled)	u16	2	Read
DALIBus #1	Zone_1_WritableCommands	Holding regs	2304	Zone 1 light command (1 = ON, 0 = OFF) Read = last written command	u16	2	Read/Write
DALIBus #1	Zone_1_WritableCommands	Holding regs	2305	Zone 1 lux setpoint - allowed values: 20, 50, 100, 150, 200, 300, 400, 500, 750, 1000, 1500, 2000, 65535 (disabled) Read = last written command	u16	2	Read/Write
DALIBus #1	Zone_1_WritableCommands	Holding regs	2306	Zone 1 switch off delay after no motion (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #1	Zone_1_WritableCommands	Holding regs	2308	Zone 1 orientation light switch-off delay (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #1	Zone_1_WritableCommands	Holding regs	2310	Zone 1 light level (0-100%) Read = last written command	u16	2	Read/Write
DALIBus #1	Zone_2_DataInfo	Input regs	2368	Zone 2 light status (ON/OFF)	u16	2	Read
DALIBus #1	Zone_2_DataInfo	Input regs	2369	Zone 2 light level (0-100%)	u16	2	Read
DALIBus #1	Zone_2_DataInfo	Input regs	2370	Zone 2 lux setpoint	u16	2	Read
DALIBus #1	Zone_2_DataInfo	Input regs	2371	Zone 2 energy consumption (Wh)	u64	8	Read
DALIBus #1	Zone_2_DataInfo	Input regs	2376	Zone 2 operation mode (0 = DALI bridge controlled, 1 = detector controlled)	u16	2	Read
DALIBus #1	Zone_2_WritableCommands	Holding regs	2368	Zone 2 light command (1 = ON, 0 = OFF) Read = last written command	u16	2	Read/Write
DALIBus #1	Zone_2_WritableCommands	Holding regs	2369	Zone 2 lux setpoint - allowed values: 20, 50, 100, 150, 200, 300, 400, 500, 750, 1000, 1500, 2000, 65535 (disabled) Read = last written command	u16	2	Read/Write
DALIBus #1	Zone_2_WritableCommands	Holding regs	2370	Zone 2 switch off delay after no motion (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #1	Zone_2_WritableCommands	Holding regs	2372	Zone 2 orientation light switch-off delay (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #1	Zone_2_WritableCommands	Holding regs	2374	Zone 2 light level (0-100%) Read = last written command	u16	2	Read/Write
DALIBus #1	Zone_3_DataInfo	Input regs	2432	Zone 3 light status (ON/OFF)	u16	2	Read
DALIBus #1	Zone_3_DataInfo	Input regs	2433	Zone 3 light level (0-100%)	u16	2	Read
DALIBus #1	Zone_3_DataInfo	Input regs	2434	Zone 3 lux setpoint	u16	2	Read
DALIBus #1	Zone_3_DataInfo	Input regs	2435	Zone 3 energy consumption (Wh)	u64	8	Read
DALIBus #1	Zone_3_DataInfo	Input regs	2440	Zone 3 operation mode (0 = DALI bridge controlled, 1 = detector controlled)	u16	2	Read
DALIBus #1	Zone_3_WritableCommands	Holding regs	2432	Zone 3 light command (1 = ON, 0 = OFF) Read = last written command	u16	2	Read/Write
DALIBus #1	Zone_3_WritableCommands	Holding regs	2433	Zone 3 lux setpoint - allowed values: 20, 50, 100, 150, 200, 300, 400, 500, 750, 1000, 1500, 2000, 65535 (disabled) Read = last written command	u16	2	Read/Write
DALIBus #1	Zone_3_WritableCommands	Holding regs	2434	Zone 3 switch off delay after no motion (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #1	Zone_3_WritableCommands	Holding regs	2436	Zone 3 orientation light switch-off delay (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #1	Zone_3_WritableCommands	Holding regs	2438	Zone 3 light level (0-100%) Read = last written command	u16	2	Read/Write
DALIBus #1	Zone_4_DataInfo	Input regs	2496	Zone 4 light status (ON/OFF)	u16	2	Read
DALIBus #1	Zone_4_DataInfo	Input regs	2497	Zone 4 light level (0-100%)	u16	2	Read
DALIBus #1	Zone_4_DataInfo	Input regs	2498	Zone 4 lux setpoint	u16	2	Read
DALIBus #1	Zone_4_DataInfo	Input regs	2499	Zone 4 energy consumption (Wh)	u64	8	Read
DALIBus #1	Zone_4_DataInfo	Input regs	2504	Zone 4 operation mode (0 = DALI bridge controlled, 1 = detector controlled)	u16	2	Read
DALIBus #1	Zone_4_WritableCommands	Holding regs	2496	Zone 4 light command (1 = ON, 0 = OFF) Read = last written command	u16	2	Read/Write
DALIBus #1	Zone_4_WritableCommands	Holding regs	2497	Zone 4 lux setpoint - allowed values: 20, 50, 100, 150, 200, 300, 400, 500, 750, 1000, 1500, 2000, 65535 (disabled) Read = last written command	u16	2	Read/Write
DALIBus #1	Zone_4_WritableCommands	Holding regs	2498	Zone 4 switch off delay after no motion (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #1	Zone_4_WritableCommands	Holding regs	2500	Zone 4 orientation light switch-off delay (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #1	Zone_4_WritableCommands	Holding regs	2502	Zone 4 light level (0-100%) Read = last written command	u16	2	Read/Write
DALIBus #1	Zone_Internal_Relay_P48_DataInfo	Input regs	2560	Internal relay light status (ON/OFF) Reflects the last DALI bridge command, not updated when the detector switches the relay	u16	2	Read
DALIBus #1	Zone_Internal_Relay_P48_WritableCommands	Holding regs	2560	Internal relay light command (1 = ON, 0 = OFF) Read = last written command	u16	2	Read/Write
DALIBus #1	Zone_Internal_Relay_P48_WritableCommands	Holding regs	2562	Internal relay switch off delay after no motion (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #2	GeneralInfo	Input regs	4096	Name DALI bus 2	str	20	Read
DALIBus #2	GeneralInfo	Input regs	4106	DALI bus 2 controller application version	buf	4	Read
DALIBus #2	GeneralInfo	Input regs	4108	Configured zones bitmask bit 0 = Zone 1 bit 1 = Zone 2 bit 2 = Zone 3 bit 3 = Zone 4 bit 4 = Internal relay bit 5:15 = reserved	u16	2	Read
DALIBus #2	GeneralInfo	Input regs	4109	Number of luminaires on DALI bus 2	u16	2	Read
DALIBus #2	GeneralInfo	Input regs	4110	Number of input devices on DALI bus 2	u16	2	Read
DALIBus #2	GeneralInfo	Input regs	4111	Measured light intensity (lux)	u32	4	Read
DALIBus #2	GeneralInfo	Input regs	4113	PIR motion status	u16	2	Read
DALIBus #2	GeneralInfo	Input regs	4115	Bitmask of DALI bus 2 error flags bit 0 = Flash write failed bit 1 = Master firmware version mismatch bit 2:31 = reserved	u32	4	Read
DALIBus #2	GeneralInfo	Input regs	4117	Bitmask of DALI bus 2 warning flags bit 0 = reserved bit 1 = Missing short address bit 2 = P40 master missing bit 3 = Control gear failure bit 4 = Lamp failure bit 5 = Bus voltage too low bit 6 = Bus shorted bit 7 = Bus overloaded bit 8:31 = reserved	u32	4	Read
DALIBus #2	GeneralInfo	Input regs	4119	Bitmask of DALI bus 2 info flags bit 0 = Identify device active bit 1:2 = reserved bit 3 = Multiple backward frames bit 4:31 = reserved	u32	4	Read
DALIBus #2	WritableCommands	Holding regs	4096	Turn all connected zones ON/OFF Read = last written command	u16	2	Read/Write
DALIBus #2	WritableCommands	Holding regs	4097	Lux setpoint - all zones Read = last written command	u16	2	Read/Write
DALIBus #2	WritableCommands	Holding regs	4098	Switch off delay after no motion - all zones (seconds) Read = last written command	u32	4	Read/Write
DALIBus #2	WritableCommands	Holding regs	4100	Orientation light switch-off delay - all zones (seconds) Read = last written command	u32	4	Read/Write
DALIBus #2	WritableCommands	Holding regs	4102	Light level - all zones Read = last written command	u16	2	Read/Write
DALIBus #2	WritableCommands	Holding regs	4104	Identify P40 master detector (1 = identify, auto-resets after execution) Read = 1 while identify is active	u16	2	Read/Write
DALIBus #2	Zone_1_DataInfo	Input regs	4352	Zone 1 light status (ON/OFF)	u16	2	Read
DALIBus #2	Zone_1_DataInfo	Input regs	4353	Zone 1 light level (0-100%)	u16	2	Read
DALIBus #2	Zone_1_DataInfo	Input regs	4354	Zone 1 lux setpoint	u16	2	Read
DALIBus #2	Zone_1_DataInfo	Input regs	4355	Zone 1 energy consumption (Wh)	u64	8	Read
DALIBus #2	Zone_1_DataInfo	Input regs	4360	Zone 1 operation mode (0 = DALI bridge controlled, 1 = detector controlled)	u16	2	Read
DALIBus #2	Zone_1_WritableCommands	Holding regs	4352	Zone 1 light command (1 = ON, 0 = OFF) Read = last written command	u16	2	Read/Write
DALIBus #2	Zone_1_WritableCommands	Holding regs	4353	Zone 1 lux setpoint - allowed values: 20, 50, 100, 150, 200, 300, 400, 500, 750, 1000, 1500, 2000, 65535 (disabled) Read = last written command	u16	2	Read/Write
DALIBus #2	Zone_1_WritableCommands	Holding regs	4354	Zone 1 switch off delay after no motion (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #2	Zone_1_WritableCommands	Holding regs	4356	Zone 1 orientation light switch-off delay (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #2	Zone_1_WritableCommands	Holding regs	4358	Zone 1 light level (0-100%) Read = last written command	u16	2	Read/Write
DALIBus #2	Zone_2_DataInfo	Input regs	4416	Zone 2 light status (ON/OFF)	u16	2	Read
DALIBus #2	Zone_2_DataInfo	Input regs	4417	Zone 2 light level (0-100%)	u16	2	Read
DALIBus #2	Zone_2_DataInfo	Input regs	4418	Zone 2 lux setpoint	u16	2	Read
DALIBus #2	Zone_2_DataInfo	Input regs	4419	Zone 2 energy consumption (Wh)	u64	8	Read
DALIBus #2	Zone_2_DataInfo	Input regs	4424	Zone 2 operation mode (0 = DALI bridge controlled, 1 = detector controlled)	u16	2	Read
DALIBus #2	Zone_2_WritableCommands	Holding regs	4416	Zone 2 light command (1 = ON, 0 = OFF) Read = last written command	u16	2	Read/Write
DALIBus #2	Zone_2_WritableCommands	Holding regs	4417	Zone 2 lux setpoint - allowed values: 20, 50, 100, 150, 200, 300, 400, 500, 750, 1000, 1500, 2000, 65535 (disabled) Read = last written command	u16	2	Read/Write
DALIBus #2	Zone_2_WritableCommands	Holding regs	4418	Zone 2 switch off delay after no motion (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #2	Zone_2_WritableCommands	Holding regs	4420	Zone 2 orientation light switch-off delay (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #2	Zone_2_WritableCommands	Holding regs	4422	Zone 2 light level (0-100%) Read = last written command	u16	2	Read/Write
DALIBus #2	Zone_3_DataInfo	Input regs	4480	Zone 3 light status (ON/OFF)	u16	2	Read
DALIBus #2	Zone_3_DataInfo	Input regs	4481	Zone 3 light level (0-100%)	u16	2	Read
DALIBus #2	Zone_3_DataInfo	Input regs	4482	Zone 3 lux setpoint	u16	2	Read
DALIBus #2	Zone_3_DataInfo	Input regs	4483	Zone 3 energy consumption (Wh)	u64	8	Read
DALIBus #2	Zone_3_DataInfo	Input regs	4488	Zone 3 operation mode (0 = DALI bridge controlled, 1 = detector controlled)	u16	2	Read
DALIBus #2	Zone_3_WritableCommands	Holding regs	4480	Zone 3 light command (1 = ON, 0 = OFF) Read = last written command	u16	2	Read/Write
DALIBus #2	Zone_3_WritableCommands	Holding regs	4481	Zone 3 lux setpoint - allowed values: 20, 50, 100, 150, 200, 300, 400, 500, 750, 1000, 1500, 2000, 65535 (disabled) Read = last written command	u16	2	Read/Write
DALIBus #2	Zone_3_WritableCommands	Holding regs	4482	Zone 3 switch off delay after no motion (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #2	Zone_3_WritableCommands	Holding regs	4484	Zone 3 orientation light switch-off delay (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #2	Zone_3_WritableCommands	Holding regs	4486	Zone 3 light level (0-100%) Read = last written command	u16	2	Read/Write
DALIBus #2	Zone_4_DataInfo	Input regs	4544	Zone 4 light status (ON/OFF)	u16	2	Read
DALIBus #2	Zone_4_DataInfo	Input regs	4545	Zone 4 light level (0-100%)	u16	2	Read
DALIBus #2	Zone_4_DataInfo	Input regs	4546	Zone 4 lux setpoint	u16	2	Read
DALIBus #2	Zone_4_DataInfo	Input regs	4547	Zone 4 energy consumption (Wh)	u64	8	Read
DALIBus #2	Zone_4_DataInfo	Input regs	4552	Zone 4 operation mode (0 = DALI bridge controlled, 1 = detector controlled)	u16	2	Read
DALIBus #2	Zone_4_WritableCommands	Holding regs	4544	Zone 4 light command (1 = ON, 0 = OFF) Read = last written command	u16	2	Read/Write
DALIBus #2	Zone_4_WritableCommands	Holding regs	4545	Zone 4 lux setpoint - allowed values: 20, 50, 100, 150, 200, 300, 400, 500, 750, 1000, 1500, 2000, 65535 (disabled) Read = last written command	u16	2	Read/Write
DALIBus #2	Zone_4_WritableCommands	Holding regs	4546	Zone 4 switch off delay after no motion (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #2	Zone_4_WritableCommands	Holding regs	4548	Zone 4 orientation light switch-off delay (seconds) Read = actual detector setting	u32	4	Read/Write
DALIBus #2	Zone_4_WritableCommands	Holding regs	4550	Zone 4 light level (0-100%) Read = last written command	u16	2	Read/Write
DALIBus #2	Zone_Internal_Relay_P48_DataInfo	Input regs	4608	Internal relay light status (ON/OFF) Reflects the last DALI bridge command, not updated when the detector switches the relay	u16	2	Read
DALIBus #2	Zone_Internal_Relay_P48_WritableCommands	Holding regs	4608	Internal relay light command (1 = ON, 0 = OFF) Read = last written command	u16	2	Read/Write
DALIBus #2	Zone_Internal_Relay_P48_WritableCommands	Holding regs	4610	Internal relay switch off delay after no motion (seconds) Read = actual detector setting	u32	4	Read/Writ